The Bell Jar Essays - Julius And Ethel Rosenberg,

The Bell Jar The Bell Jar People's lives are shaped through their success and failure in their personal relationships with each other. The author Sylvia Plath demonstrates this in the novel, The Bell Jar. This is the direct result of the loss of support from a loved one, the lack of support and encouragement, and lack of self confidence and insecurity in Esther's life in the The Bell Jar. It was shaped through her success and failures in her personal relationships between others and herself. Through life, we often lose someone we loved and cared deeply for and supported us through life. This is demonstrated by the loss of a loved one when Esther's father died when she was nine. "My German speaking father, dead since I was nine came from some manic-depressive hamlet in the Prussia." (Sylvia Plath page 27.) Esther's father's death had showed that she was in need of a father figure for love, support and to act as a model for her life. Esther grew up with only the one influence of a parent, her mother. Often times the loss of a friendship can be a great loss of support and confidence within our lives because we can lose them forever. This is demonstrated when Buddy Willard Esther's boyfriend break up. "He told me that his annual fall chest x-ray showed he had caught tuberculosis...in the Adirondacks" (Sylvia Plath pg. 58.) Buddy and Esther break up due to the fact that he was not very honest with her in many ways. He did not have the courage to admit to a certain side of his character and not only that Buddy was diagnosed with an illness but he had other relationships aside from Esther. Therefore Esther experienced another loss of a loved one. Within life, we gain the support from someone that helps us get through life but often times leaves us when we need them most. This is proven when Doreen; Esthers co-worker at the modeling magazine begins to lose contact with Esther through life "Doreen is dissolving... none of them mean anything anymore" (Sylvia Plath pg.17) Doreen begins to lose contact with Esther throughout life, just when Doreen had opened new doors to her. Esther was coming through a very difficult time in life, when Doreen started drifting away from Esther. Once again, Esther experienced the loss and support of a great friend and advocate. Ones' life is made up by framework. You gather friends and folks together and in this framework it clarifies your identity. You articulate and express opinions. You articulate and express opinions. In framework and talk, you develop behavior patterns and priorities and define framework in terms and languages. Esther did all this in her life. But then she forgot who she was. She forgot her framework of reference and she talks about success and failures and despair. Individuals, need encouragement and support from loves ones to guide one through life. This is seen in the lack of support and encouragement displayed when Esther's mother fails to support and encourage Esther with her aspirations. No matter what Esther had wanted to do with her life, her Mother had always wanted her to learn the skills of shorthand because she would always have that skill in her life and also that was the one thing her Mother had experienced in life. As a result, her Mother failed to enhance Esther with her aspirations that she wanted from life. We need the sustenance and assurance from not only loved ones in life, but also from others. This is demonstrated when Jay Cee, Esther's present boss asked Esther what she wanted to do with her life. Esther did not have any solid idea as to what she wanted to do with her life. "You'll never get anywhere like that." (Sylvia Plath page 27) Esther did not know what she especially wanted with her life. Jay Cee stated to Esther that not having an idea of what she wants, will not get her very far because Esther is lacking a few skills. Consequently, Esther lacked the support and helpfulness from her friend and colleague. Throughout life one also needs the motivation and provisions from those that influence one's lives. This is demonstrated by Esther's Class Dean who upheld Esther through her high school years. "I had a way of persuading...interesting experiment." (Sylvia Plath page 29.) Her Class Dean supported Esther in her way of thinking and her thrive for learning which in turn, she was awarded for her learning by receiving many scholarships. Therefore, Esther had the support of her Class Dean in

Analysis to Declaration of independance essays

Analysis to Declaration of independance essays In response to the questions to consider, Spain had many positive opportunities come about from the voyage of Christopher Columbus. One major thing was the fact that they now could brag about their discovery of America for all time, as we know it. Even today they think that America is the way it is because of them. (I spent 2 long years there) But more realistically, they gained territory for their church. One of the first things done in the New World was work of conversion to the heathens to Christianity. Columbus, although being Portuguese, gave all of the countries a Spanish name to pay respect to the country that made his voyage possible. The major plans of Columbus for this new found and mysterious breed was of course to convert the people to their " holy faith " as he puts it. One of the first things that the Indians did when they saw Columbus was bow down to him and give him drinks, food and other gifts. Their reasoning for doing such was because they thought Columbus was the "Man from Heaven ". Little did they know he was a mere explorer and trespasser that would bring them bad fortune and many diseases along with power-hungry Anglo-Saxon Englishmen. However, the Europeans set forth the groundwork for a more productive people that would help the world advance immensely in the years to come. Columbus also talks of the geographical location and climate. One remark where he refers to the power of the sun in this area demonstrates that where he comes from is not quite as hot and was quite a change for he and his crew. ...

How Crime Scene Insects Reveal the Time of Death

How Crime Scene Insects Reveal the Time of Death When a suspicious death occurs, a forensic entomologist may be called to assist in processing the crime scene. Insects found on or near the body may reveal important clues about the crime, including the victims time of death. Insects colonize cadavers in a predictable sequence, also known as insect succession. The first to arrive are the necrophagous species, drawn by the strong scent of decomposition. Blow flies can invade a corpse within minutes of death, and flesh flies follow close behind. Soon after coming, the dermestid beetles, the same beetles used by taxidermists to clean skulls of their flesh. More flies gather, including house flies. Predatory and parasitic insects arrive to feed on the maggots and beetle larvae. Eventually, as the corpse dries, hide beetles and clothes moths find the remains. Forensic entomologists collect samples of crime scene insects, making sure to take representatives of every species at their latest stage of development. Because arthropod development is linked directly to temperature, she also gathers daily temperature data from the nearest available weather station. In the lab, the scientist identifies each insect to species and determines their exact developmental stage. Since the identification of maggots can be difficult, the entomologist usually raises some of the maggots to adulthood to confirm their species. Blow flies and flesh flies are the most useful crime scene insects for determining the postmortem interval or time of death. Through laboratory studies, scientists have established the developmental rates of necrophagous species, based on constant temperatures in a laboratory environment. These databases relate a species life stage to its age when developing at a constant temperature, and provide the entomologist with a measurement called accumulated degree days, or ADD. ADD represents physiological time. Using the known ADD, she can then calculate the likely age of a specimen from the corpse, adjusting for the temperatures and other environmental conditions at the crime scene. Working backward through physiological time, the forensic entomologist can provide investigators with a specific time period when the body was first colonized by necrophagous insects. Since these insects almost always find the corpse within minutes or hours of the persons death, this calculation reveals the postmortem interval with good accuracy.

Guy Body Image Research Paper Example | Topics and Well Written Essays - 1250 words

Guy Body Image - Research Paper Example As a result, the society is forced to try to attain the physical unattainable perfection as featured prominently in the mass media (Government of Western Australia 1). The influence has been significant in as indicated in various researches. For example, a study carried out showed that looking at fashion magazines for a moment lowered the self-esteem of over 80 percent of women (Government of Western Australia 1). The media have failed to acknowledge that both males and females come in all different shapes and sizes. Therefore, the representation of one body type as being ideal is unrealistic (Government of Western Australia 1). This leads to adoption of harmful behavior to both males and females as they try to attain the images depicted on the media. Moreover, the worry about body image has also manifested in males. There have been an increasing number of males under pressure to maintain a high level of fitness and physical perfection. As a result, most males have been spending most of their money and times in gyms, beach, and sporting clubrooms. Moreover, they have adopted some strange feeding habits, and use of drugs to enhance body image (Government of Western Australia 1). Media have a profound impact on the female body. The influence is usually rampant to the teenagers. The media have led to the notion that the value of women is based on the outward appearance (Serdar 1). The images depict an impractical standard of feminine beauty (Serdar 1). This in the end has a powerful influence on the way women view themselves. According to the view of the mass media, thinness is considered perfect, and a key thing for women to be attractive (Serdar 1). The figure has been commonly highlighted through various ads. Such images in the ads, television, and music portray the perfect woman (Serdar 1). Moreover, the media have been full of images of females that possess these unique attributes. As a result, this makes it usual

Interview Experience and Making Presentations Research Paper

Interview Experience and Making Presentations - Research Paper Example The process of doing a job interview is regarded as one of the most critical processes in job search. People engage in interviews with ultimate caution, and this translates into a nervous breakdown at times. Interview processes are also done for other issues but job interviews top the list in my most memorable engagements. My first encounter with such a practice was successful due to certain aspects. I went for the job interview with high hopes but I was also extremely cautious not to end up unsuccessful. My application targeted the post of a data entry clerk in a research firm. It was my first part-time job search, and it was extremely significant to me. Basically, the interview embodied a strategic conversation that stemmed out of purpose. My goals included proving to the prospective employer that I certainly had the skills, background, and the relevant ability required for the job. These qualities help an individual in assuring the employer that she/he can fully fit into the compa ny and its core culture (Allen, 2011). My experience was quite challenging, but the results were impressive since I was accepted into the company. I answered the questions comfortably and portrayed other personality attributes that were instrumental. Exemplary interpersonal and communication skills were evident, as well as confidence and enthusiasm among others. The interview was successful due to the fact that I was able to answer the questions in the best way. This can be attributed to the issue of merit, but it was also influenced by extensive research about the company. I carried out some research about the company prior to the interview; thus, I had relevant knowledge on the interviewer’s expectations. I may comfortably state that this was the biggest reason as to why I got employed. However, it is pertinent to note that other issues also contributed towards the achievement. This can be exemplified by my ability to volunteer crucial personal information about my strength s and weaknesses also enhanced my quest. B. Describe an interview you have had (or know about) that did not go well. Speculate as to what went wrong. Explain how the interview could have been successful. My second experience was also a job interview and it characterized most aspects that relate to such practices. In this case, I was also targeting a part time job in a manufacturing company during the holidays. I was confident that I would be successful since I had already participated in a similar exercise in the past. The professional part of the conversation was evident, and I managed to convince the interviewer that I had great interest in a supervisor’s job. I proved to the interviewer that I was the right person for the job through my intense knowledge of the company. This knowledge resulted from research about the company and general knowledge obtained from previous stints in school. My dress code depicted the image of a successful and ambitious person, and it unequivoc ally propelled my chances to greater heights. I answered the questions in the best way possible and maintained my composure throughout the interview. However, there are aspects that I failed to consider during the interview, and they specifically led to complications and disqualification in the long run. There was no doubt that I did merit for the job, but these smaller aspects that I failed to observe changed the entire scene. Apparently, a successful interviewee should not mention the weaknesses of his/her previous employer (Donald, 2002). After my first part time job I had problems with my former employer concerning salary issues. During my second interview, I raised these issues hoping that my prospective employer would consider my

Types of Foundations, Building Frames and Partitions

Types of Foundations, Building Frames and Partitions TASK 1.1 Alternative sub-structure solutions: In any building the superstructure, substructure (foundations) and the supporting soil acts in a coordinated way to give structural stability. Therefore the foundations act as connection between superstructure and the ground. Successful foundations should be: Foundations must be at minimum depth and size without exceeding the allowable bearing capacity of the soil. They must be strong enough to provide stability to the supporting structure. They must be able to withstand natural ground movements from corrosive chemicals, frost, moisture and heat. They must be economical and sustainable. For our Englemere Village project we used Strip and Pad foundations. Foundations can be classified as: Shallow Foundations Strip Foundations Traditional Strip Foundations Trench fill Foundations Combined- Stepped Foundations Pad Foundations Rafts Pier and Beam Foundations Deep Foundations Piled Foundations Displacement Piles Replacement Piles Shallow Foundations The foundations which are placed beneath the lowest part of the structure and near to the ground level are shallow foundations. Strip Foundations Strip foundations are the most common foundations used in construction, it is a strip of concrete running under all load bearing walls. The depth and the width of the strip foundations depends on the nature of the soil and superstructure load, they can be 500-700 mm wide and as deep as per the nature of the soil/ground. Strip foundations can be either traditional strip or trench fill and both can be stepped. Traditional Strip Foundations Strip foundations are used where soil has good bearing capacity. Load is transmitted at 45 degrees angle from the base of the wall. The width of strip foundation is three times the width of the wall. Thickness should be at least 150 mm, but 300 mm is most commonly used. Depth should be 450 mm minimum measured from finished ground level to protect from frost attack. See Appendix 1. Trench fill Foundations Trench fill is quicker and more cost effective than traditional strip. The thickness should not be less than 500 mm and should finish 150 mm below ground level. Trench should be dug to a depth where subsoil provides sufficient load bearing capacity, usually it is 1m deep. See Appendix 2. Stepped Foundations Stepped foundations are used on sloping sites. As top of foundation has to be level and on slopping sites foundations can end up too deep. Stepped foundations reduce the amount of excavating and cost. The step should not be bigger than the thickness of foundation and should work with heights of the bricks. Overlap should be at least twice the height of the step. Raft foundations Reinforced concrete raft is used when bearing capacity of soil is low. It spreads the load from structure over a large area. Reduces the amount of excavating. Concrete raft is usually at least 150 mm thick. Sometimes the raft is thickened under load bearing walls. See appendix 3. Pad foundations Pad foundations are used when isolated loads need to be supported, spreading the load to the ground below. They are used for columns or framed buildings. Pad foundations are constructed from reinforced concrete. See Appendix 4. Pier and beam foundations Pier and beam foundations are made from brick, block or timber piers on concrete pads. Beams sit on the piers and are usually raised above the ground to create a crawl space underneath. Pier and beam is a cost effective foundation for smaller buildings. See appendix 5. Deep Foundations The foundations that are constructed below ground level while using artificial arrangements such as piles can be termed as deep foundations. Pile foundations Pile foundations are used to transfer load of superstructure through weak soil onto strong soil or rock. Piles can be displacement or replacement. Pile caps or beams sit on top of the piles. See appendix 6. Displacement piles are driven into the ground by pushing the soil out of the way. They are friction piles. This method is very noisy and vibrating. But there is no soil to be removed from site. One of displacement methods is helical screw piling. A helical pile consists of a galvanised steel shaft onto which is welded a series of circular steel plates. They are power drilled in to the ground. Advantages are: fast installation, vibration and noise free, sustainability (can be removed and reused). Replacement piles remove soil and replaces with reinforced concrete. They are end bearing piles. All soil needs to be removed from site but it is less vibrating and noisy than displacement pilling. Causes of Foundation Failure Failure in transferring the load between superstructure and soil can lead to building movement and cracking, but failure of foundations cannot be held alone responsible for cracking there can be other reasons for these kind of damages. Seasonal movements, chemical attack, building alterations, trees, soil creep and variable ground conditions are few causes of foundation failures. Alternative systems for structures, envelope and roof coverings Constructed structures start with architectural and engineering plans, however all structures follow basic design steps as follows; Preparing the site Installing foundations Building the framework Enclosing the structure Finishing the exterior and interior Completing the site Building the Framework The framework depends on the foundations as foundations provide base for building the framework. Floors, interior and exterior walls, ceilings and roof are included in the building process of framework. Therefore framework provides a rigid shape and structure to the buildings. Brick and block is a traditional method of building. Brick and block houses use a cavity wall construction with a gap filled with insulation. These walls are load bearing, they support floor joist and roof. In MMC (modern method of construction) systems for structures framing process is mostly done offsite and are only erected on site. MMC system provides much quicker way of building. There are different types of frames as listed below are used in MMC systems for structures. Steel frame Timber frame Portal frame Concrete frame Structural Insulated Panels (SIPs) Insulated Concrete Framework (ICF) Steel frame Steel frame construction is a quick way of building as all the parts are manufactured offsite. It is a lightweight structure compared to traditional masonry or block work. Steel frame can be used from domestic housing to really tall skyscrapers and it is a sustainable way of building as steel can be recycled many times. The skeleton is formed from vertical steel columns and horizontal I beams. All the loads are transferred to foundation through columns. Timber frame Timber frame panelling system is another fast construction method used in domestic housing. All panels and roof trusses are made offsite and erected on site in a number of days. It has 30% shorter building times than brick and block. This means the house is water tight more quickly and other trades can start work sooner. Timber frame has higher insulation properties than brick and block. Portal frame Portal frames are used for a single storey construction which requires a large floor space for example: warehouse, factories or supermarkets. It has no intermediate columns that mean large open space areas can be created within the structure. It is manufactured offsite – fast construction. Concrete frame RC (reinforced concrete) frame is a very common type of building. The skeleton is made out of vertical columns, horizontal beams and slab in between. Concrete is cast into formwork. SIP (structural insulated panels) SIPS have very good insulation value and structural strength. SIPS panels can be used in walls, floors and roofs for domestic, industrial and other constructions. SIPS are made from Polystyrene (EPS) sandwiched between two Oriented Strand Boards (OSB) making them lightweight and quick to erect by interlocking them together. ICF (Insulated Concrete Framework) ICF involves building a site with laying a series of hollow blocks, made up of expanded polystyrene (EPS) and then are pumped with ready-mixed concrete. EPS provides a high insulation wrapping around the concrete once the structure is finished. This framing system not only provides speedy construction but also it gives a protection against sudden climatic changes. Although adopting ICF will cost higher than an average timber frame build but it can provide reduced construction times and lower energy bills. Thin Joint Thin joint provides improved thermal performance and building accuracy over conventional brick and block construction. The structures are made with large aircrete block and quick drying mortar. 75% less mortar is used. This thin joint framing can be erected in no time, furthermore it provides a stability to the overall structure and an adaptation to extend the building at later date. The MMC building systems are used in order to save construction time and the cost of the construction but they must be used after reviewing the local construction laws and other weather conditions. Building Envelope The building envelope acts as a physical separator between an exterior and interior environment, therefore it can be termed as the building enclosure. It provides a shell to maintain an indoor environment of any building, it also helps in facilitating the climate control. Building envelope is exterior skin of the building that separates interior from exterior. It protects building from rain, wind and sun. Envelope includes external walls and roofs. External walls used in an envelope can be classified as follows Cavity Walls Stone cladding Load bearing stone masonry walls Glazed concrete blocks Wood cladding External walls in making an envelope must provide the bearing, insulation and shape to the building. To give more insulation to the external walls they must have insulating fillings, separate insulating layer and air insulating layer. Roof coverings Roof covering must bear the following functions; Protection of the building against rainfall, snowfall etc and other weather conditions. Protection against cold, heat, overheating, wind and noise. Protection against fire. To cover all these protections roof covering must have the following items in its architectural design Water proofing insulation Thermal insulation Wind stability Sound insulation Roofs are divided into Flat and Pitched. Flat roofs could be: Ash felt, felt, EDPM, Fibre glass, glass. Pitched roofs could be: lean to, couple, purlin, mansard, trussed, hipped, trussed rafter, attic truss. MMC alternatives for partition walls Partitions are the vertical walls or panels that are used to divide portions of the building and they can be classified as load bearing or non-load bearing. Traditionally timber was used as partitions but with the advancement in construction methods and the use of light weight partitioning and light weight insulation block, its use as a partition is decreasing significantly. Partitions can be constructed using various materials, but the most common types of partitions are: Timber Stud Partitions. Metal Stud or Dry wall Partitions. Glass Partitions. Sliding Partitions Room dividers Re-locatable office Partitions Timber Stud Partition Timber stud partitions are non-load bearing and light weight partitions. Timber stud partitions consist of wooden framework between horizontal head and sole pieces at the top and bottom of the framework and a series of uprights called studs holding the whole framework. The noggings are intermediate stiffening material placed between the studs to ensure the overall stability of the framework. Timber frame partitions are formed with butt joints or framing anchors to significantly facilitate the low labour cost and speed of erection. Plasterboard is usually used as a covering material for timber partitions. Metal Stud or Dry wall Partitions Metal stud partitions are non-load bearing partitions consisting of a metal studding framework. This metal studding makes the partitions light weight but comparatively strong and stable than timber stud partitions. They can be covered with ordinary plasterboards or special fire resistant sheets, which on final sealing can make these partitions sound proof as well as fire resistant. Metal stud partitions are quick and easy to erect, they are cost effective, sustainable for all types of buildings and they are available in variety of finishes. Due to these strong characteristics metal stud partitions are mostly used in public buildings and hospitals. The metal studs are manufactured from galvanised steel sheet folded into various shaped sections which slot into each other. The sections are produced in various lengths ranging from 2.4 m to 6 m in length and widths ranging from 50 mm to 146 mm. Glass partitions Glass fulfils an important role in creating divisions between indoors and out as well as between individual interior spaces. The technical advances in the material mean that it is suitable for a wider range of applications than ever before. †¢ Double single glazed options †¢ Excellent acoustic performance up to 47db (Rw) †¢ Attractive and Stylish †¢ Full range of manifestation options †¢ Wide range of profile colours †¢ 10mm and 12mm glazing †¢ Option of standard height or full height doors Single glazing can be used where clean lines and an aesthetically pleasing design are essential. The partitioning is designed with the minimum amount of framework to give a frameless appearance. To maintain the open feel of the office environment frameless doors or framed glass doors are fitted within the system using floor pivots and patch fittings or floor springs if required. Where desired or in order to comply with building regulations, fully glazed panels have manifestation film applied to them. These can be used to simply highlight the presence of the partitions, create individual designs or incorporate company logos using either 10/12mm toughened glass depending on the height of the partition, glazing is achieved with the use of clear glazing gaskets that remove the need for silicone around the perimeter of the system. Vertical silicone joints maintain the visual simplicity of the product or clear plastic jointing sections to provide dry joints between glass panels. Appendix 1 Traditional strip foundations Appendix 2 Trench fill foundations Appendix 3 Raft foundations Appendix 4 Pad foundations Appendix 5 Pier and beam foundations Appendix 6 Pile foundations

The Greek Polis

The polis is the city-state of ancient Greece where Greek politics, commerce and creative culture was centered. It developed from the Archaic period and is considered the ancestor of the terms city, state and citizenship. It was the central urban area that may have some degree of rule over the surrounding countryside. Among the Greek polis were Athens, Thebes and Sparta which were considered independent with each other. The polis is typically bounded around a citadel or an acropolis and would essentially have a market called the agora and would usually have one or more places of worship and a gymnasium. The Greeks considered the polis or city-states as a unique institution because in ancient times, it was the first gathering of people wherein the rulers or officials were elected by the people and laws were passed. Although the polis was composed of several tribes or demes, it was ruled not by a particular king or oligarchy but rather considered as a political entity ruled by the inhabitants or citizens themselves. To some extent, there is a high degree of citizen involvement and participation in the management of the public organization in a polis. The polis was considered as the most significant contribution in politics of the Greek people. The fundamental difference between the ancient Greek polis and a modern day country city like that of Western Europe or America is that the Greeks did not consider the polis as under any sovereignty while a modern age city is necessarily under a sovereign country or state. In other words, the polis is an autonomous entity while a modern city is positively positioned in a sovereign state. The polis is not identified by territory but rather by the citizenship of its people whereas a modern city is generally set apart by land area and population. Their similarities lie greatly in them being both centers of commerce, artistry, politics and the melting pot of state development.